Technology Transfer Area

IMPORTANT NOTICE

July 22, 2024 UPDATE

Due to some recent results we now discourage 3d printed versions of the PrimerCube.

Important Notice: Do Not Modify the PrimerCube Design

We must emphasize that no modifications should be made to the design of the PrimerCube. Any alterations could lead to poor results and potential harm to users. Our original PrimerCube design has been rigorously tested and proven superior to any other versions currently available. To create an authentic PrimerCube, it's essential to use the specific materials we used in the original PrimerCube. Using alternative materials, such as 3D printing a PrimerCube, may pose risks to users and is no longer recommended. We also no longer help individuals make their own PrimerCube. The reason for this change is because of situations like the one below.

Performance Comparison and Safety Concerns

After thoroughly comparing the performance of our original PrimerCube with that of a copy produced in the Czech Republic, we have identified significant concerns. The Czech version does not provide the same benefits for critical issues as our original design. Therefore, we no longer endorse or recommend the copy PrimerCube design offered at [www.primercube.eu]

This decision was not made lightly. After extensive discussions within the PrimerField Foundation, we unanimously decided to sever all ties with the Czech company. The product sold at [www.primercube.eu] should be considered a counterfeit and not representative of the genuine PrimerCube.

Due to the substantial differences in performance over the past three years, we cannot guarantee the long-term safety of the Czech version. In February 2020, David LaPoint explicitly warned the Czech company about altering the proven design. Despite these warnings, the Czech company proceeded to significantly modify both the internal and external design of their product. Years of use have shown that, although their version provides some benefits, it does not match the performance of our original design. The notable difference in performance between the authentic PrimerCube and the Czech version suggests potential long-term safety concerns. While we are not asserting that the Czech cube is unsafe, it requires at least two more years of use to fully assess its safety. Although we regret this situation, our review of the results obtained by users of the Czech cube has made it clear that this version is inferior and its safety is uncertain. The results obtained from users of the Czech cube indicate that the Czech cube is no more effective than just the bowl shaped arrays alone. So if you are considering purchasing a PrimerCube we strongly suggest that you instead acquire just the bowl shaped array as that will be just as effective or even more effective than the Czech cube. In addition the bowl shaped arrays do not appear to have any saftey concerns as they have been in use for many years without any negative issues.

Adherence to Original Design

We strongly implore you to follow the design we provided previously without any modifications. Each component of this design is meticulously crafted for a specific purpose. Alterations could lead to subpar performance or potential harm to users. Even altering the exact materials we used in the original PrimerCube can lead to poor performance.

We take the health, happiness, and safety of PrimerCube users very seriously. This is why our original design underwent years of careful testing before being made open source. The Czech company's decision to release their modified version without adequate testing was, in our opinion, reckless.

As soon as we realized that the Czech version was not producing the same results as our original design, we immediately decided cut all ties with that company and let everyone know why. The most recent model we received from them was carefully evaluated, and it was found that even the core magnetic array did not meet the specifications of our original PrimerCube. We wish it was not this way, but we want everyone to have the best this technology can offer without any possible negative issues.

Important Notice for PrimerCubes Production

If you choose to manufacture PrimerCubes, it is crucial that you adhere strictly to the original design specifications. Modifying the design is done at your own risk, and you will be fully responsible for any consequences that may arise. This technology is powerful and not intended as a toy. If devices based on this technology are not built according to our exact specifications, serious and potentially dangerous outcomes could occur. Please consider this warning carefully before attempting to produce altered versions of this technology.

Injection Molds

Due to concerns over the production of counterfeit PrimerCubes, we now require prior approval for the use of our injection molds. Allowing unauthorized use of these molds could result in PrimerCubes that appear identical on the outside but contain critical modifications inside that render them ineffective or even dangerous.

This precautionary measure is in place to protect innocent users from potential harm caused by unwise alterations to our original design. We appreciate your understanding and cooperation in ensuring the safety and integrity of PrimerCubes.

To be allowed access to these files you must contact us and prove that you are a large manufacturing company that will follow our exact design. The technology is still open source but we at the PrimerField Foundation no longer will help those who intend to vary in any way from the exact specifications we provide for free to approved manufacturing companies. Our only reason for doing this is to protect people from those who are only interested in making money off of this technology. This technology was a gift from God to all of us and we will not help anyone who is placing profits over people misuse this gift .